Dow DOWSIL 1-2577 RTV Silicone Conformal Coating Clear 453 g Bottle - PF1257701

$204.69
Description

Description

What it is. Dow DOWSIL 1-2577 is a one-part, transparent RTV silicone conformal coating for rigid and flexible printed circuit boards. Lab Pro carries it in a 453 g bottle. This solvent-borne silicone resin solution cures at room temperature into a firm, tough, abrasion-resistant elastoplastic surface that protects assemblies from moisture, atmospheric contaminants, and handling damage. As a conformal coating silicone, it stays flexible across a wide temperature range.

Approvals that matter. DOWSIL 1-2577 is approved to MIL-I-46058C, Amendment 7, and IPC-CC-830, Amendment 1, is UL 746E recognized; and carries a UL 94 V-0 flammability rating, according to Dow. Those approvals are why it is specified in aerospace, defense, automotive, and industrial electronics, where the coating on a board must match a named military, industry, or UL requirement on the drawing or work instruction. Matching the coating to the cited specification avoids rework and failed audits.

Fast, room-temperature cure. Dow lists a tack-free time of about 7 minutes at 25 °C, or about 1.3 minutes at 60 °C and 15% relative humidity. Heat can accelerate cure, but only after the solvent has flashed off; a typical schedule for a 3-mil coating is 10 minutes at room temperature followed by 10 minutes at 80 °C. If the coating blisters, allow more room-temperature flash time before the oven.

Application flexibility. The coating can be sprayed, brushed, flow coated, dipped, or applied by automated pattern coating. For spraying, we recommend solvent dilution up to 60%, while dipping can use the material as supplied or diluted for a thinner film. A UV indicator lets inspectors confirm coverage under black light, and good adhesion allows use with many no-clean and lead-free solders without a separate primer. That flexibility suits both small repair benches and high-volume production lines.

Electrical and physical properties. Distributor data sheets list a dielectric strength of 400 volts/mil, a volume resistivity of 5.0 × 10^13 ohm·cm, a dielectric constant of 2.74, and a mixed viscosity of about 950 cP. Dow lists a cured specific gravity of 1.11 and a Shore A hardness of 80, and the coating is rated for service from -45 to 200 °C. Shelf life is 36 months from the date of manufacture.

Safety and handling. Because DOWSIL 1-2577 is supplied in solvent, the liquid is flammable; a distributor lists a flash point of 5 °C. Apply it with ventilation, keep it away from heat and ignition sources, and wear gloves and eye protection. Moisture starts the cure, so keep containers and dip tanks covered and use dry solvent for dilution. Read the SDS before use. Those precautions protect both the operator and the coating quality.

Technical Specifications

Manufacturer Dow
Product DOWSIL 1-2577 Conformal Coating
Composition One-part silicone resin solution (solvent-borne)
Cure RTV (moisture); heat accelerated after solvent flash-off
Color Clear, transparent
Viscosity ~950 cP
Specific Gravity 1.04 uncured · 1.11 cured
Tack-Free Time 7 min at 25 °C · 1.3 min at 60 °C/15% RH
Typical Cure (3 mil) 10 min at room temperature, then 10 min at 80 °C
Hardness Shore A 80
Dielectric Strength 400 volts/mil (16 kV/mm)
Volume Resistivity 5.0 × 10^13 ohm·cm
Dielectric Constant 2.74 at 100 Hz and 100 kHz
Flammability UL 94 V-0
Approvals MIL-I-46058C Amend. 7 · IPC-CC-830 Amend. 1 · UL 746E
Inspection UV indicator
Service Temperature -45 to 200 °C
Flash Point 5 °C (distributor data)
Shelf Life 36 months from date of manufacture
Package 453 g bottle

Applications / Common Uses

  • Rigid and flexible circuit boards: protective coating against moisture and contaminants
  • Military and aerospace electronics: coating to MIL-I-46058C and IPC-CC-830
  • Automotive and industrial controls: abrasion-resistant protection across -45 to 200 °C
  • Lead-free and no-clean assemblies: good adhesion without a primer
  • Automated coating lines: spray, dip, flow, or pattern coating with UV inspection

Storage, Handling & Shipping

Store DOWSIL 1-2577 in its original, tightly closed container in a cool, dry, well-ventilated area approved for flammable liquids, away from heat and ignition sources. Keep moisture out, since moisture starts the cure: close containers immediately, cover dip tanks when not in use, and use dry solvent for thinning. Use within the 36-month shelf life. Ships as a flammable liquid; consult the SDS for handling and disposal.

  • Storage: Flammable liquid storage; cool, dry; away from ignition sources
  • Moisture: Keep containers closed and dip tanks covered
  • Shelf life: 36 months from date of manufacture
  • Shipping: Flammable liquid; hazmat charge may apply

Related Categories & Services

Services

FAQs

What is the difference between MIL-I-46058C and IPC-CC-830?

MIL-I-46058C is a legacy U.S. military specification for conformal coatings, while IPC-CC-830 is the industry qualification standard that has largely replaced it in many programs. Many drawings still cite one or both, so a coating approved to both, like DOWSIL 1-2577, simplifies compliance. Check which specification your drawing cites.

How do I check conformal coating coverage?

DOWSIL 1-2577 contains a UV indicator, so coated areas fluoresce under black light. Inspectors can quickly spot missed areas, thin spots, or contamination on the board, and automated optical inspection systems can use the same fluorescence for in-line checks. Inspect under consistent lighting conditions.

Can DOWSIL 1-2577 be removed for rework?

Silicone conformal coatings can typically be removed locally for repair using appropriate silicone removers or mechanical methods, then the area recoated. Follow your rework procedure and test removal methods on a sample board first to avoid damaging components. Recoat repaired areas with the same coating, where possible, to keep protection consistent.

Why did my conformal coating blister in the oven?

Blistering usually means solvent was still trapped when you applied heat. Allow more room-temperature flash-off time before oven cure, especially for thicker coats, and avoid applying the coating too thick in one pass. Thin, even coats cure most reliably.

What is conformal coating?

Conformal coating is a thin protective film applied over a printed circuit board that conforms to the shape of its components. It shields the assembly from moisture, dust, chemicals, and handling damage. Silicone coatings such as DOWSIL 1-2577 stay flexible across wide temperature ranges.